Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2015-08-21 00:10:02

lanakane
Member
Registered: 2015-08-20
Posts: 4

First time user - Stuck in a loop after flashing

Hi folks,

This is the first time Im working with this device. (Limited embedded b/g). I followed the steps for setup here : https://github.com/Proxmark/proxmark3/wiki/OSX

Right after  step : 23. Disconnect the Proxmark3 from the USB I entered the weird state with proxmark where the orange/red light continues to persist with some clicking noises every few seconds.

I followed the steps exactly as in the wiki.  Also here is the log after flashing

[== Undefined ==]
./client/flasher /dev/cu.usbmodemfd121 armsrc/obj/fullimage.elf 
Loading ELF file 'armsrc/obj/fullimage.elf'...
Loading usable ELF segments:
0: V 0x00102000 P 0x00102000 (0x00024cb0->0x00024cb0) [R X] @0x94
1: V 0x00200000 P 0x00126cb0 (0x00001a78->0x00001a78) [RW ] @0x24d44
Note: Extending previous segment from 0x24cb0 to 0x26728 bytes

Waiting for Proxmark to appear on /dev/cu.usbmodemfd121. Found.
Entering bootloader...
(Press and release the button only to abort)
Waiting for Proxmark to reappear on /dev/cu.usbmodemfd121...... Found.

Flashing...
Writing segments for file: armsrc/obj/fullimage.elf
 0x00102000..0x00128727 [0x26728 / 308 blocks].................................................................................................................................................................................................................................................................................................................... OK

Resetting hardware...
All done.

Have a nice day!

Any help towards fixing it would be highly appreciated. (Or even a nudge in figuring out what is wrong)

Offline

#2 2015-08-21 03:40:18

marshmellow
Contributor
From: US
Registered: 2013-06-10
Posts: 2,302

Re: First time user - Stuck in a loop after flashing

Unplug pm3, hold pm3 button, plug it in and flash the bottom while holding pm3 button

Offline

#3 2015-08-21 19:53:14

lanakane
Member
Registered: 2015-08-20
Posts: 4

Re: First time user - Stuck in a loop after flashing

marshmellow wrote:

Unplug pm3, hold pm3 button, plug it in and flash the bottom while holding pm3 button

No luck with it so far. I just see the message : Waiting for Proxmark to appear on /dev/cu.usbmodemfd121

pm3 is not being detected it looks like.

Offline

#4 2015-08-21 20:28:17

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: First time user - Stuck in a loop after flashing

have you done the blacklisting?...

Offline

#5 2015-08-22 01:06:30

lanakane
Member
Registered: 2015-08-20
Posts: 4

Re: First time user - Stuck in a loop after flashing

iceman wrote:

have you done the blacklisting?...


Nope. Could you please give me a link or some reference to what it is that I am missing?

Offline

Board footer

Powered by FluxBB