Proxmark developers community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

#1 2008-11-19 23:07:57

d18c7db
Contributor
Registered: 2008-08-19
Posts: 292

Proxmark3 board build pictures

I finally got around to posting some pictures on flickr of my first board I built last week. Took me about 6 hours of hand soldering everything.

Offline

#2 2009-02-26 09:43:45

ajoakim
Member
Registered: 2009-02-21
Posts: 4

Re: Proxmark3 board build pictures

Would you be able to post the schismatics for your jtag unit
thank you

Offline

#3 2009-02-26 13:57:19

n0t
Contributor
Registered: 2008-11-24
Posts: 26

Re: Proxmark3 board build pictures

ajoakim wrote:

Would you be able to post the schismatics for your jtag unit
thank you

Read this post:
http://proxmark.org/forum/viewtopic.php?id=149

Offline

#4 2009-02-26 19:00:20

ajoakim
Member
Registered: 2009-02-21
Posts: 4

Re: Proxmark3 board build pictures

I am using this JTAG  , the one in the manual is vague as to what the schematics are, if some one wants to clear it up i would be great full.0.jpg

Last edited by ajoakim (2009-02-26 19:01:52)

Offline

#5 2009-02-27 15:55:44

n0t
Contributor
Registered: 2008-11-24
Posts: 26

Re: Proxmark3 board build pictures

Did you try this?  It's from the manual.
Pins 3, 4 and 5 are the same.
2vsniae.jpg

Offline

#6 2009-03-03 22:21:14

ajoakim
Member
Registered: 2009-02-21
Posts: 4

Re: Proxmark3 board build pictures

Yeap i tried that it didn't work i guess i fried my Amtel Chip sad, but i didn't solder it for that long one pass with a 14w iron did it. Hummm how can i check to see if the chip is working, with out a scope.

Offline

#7 2009-03-04 02:45:18

shinechou
Contributor
Registered: 2008-10-20
Posts: 35

Re: Proxmark3 board build pictures

n0t wrote:

Did you try this?  It's from the manual.
Pins 3, 4 and 5 are the same.
http://i39.tinypic.com/2vsniae.jpg

I'd tried it but didn't work too!

Offline

#8 2009-03-04 14:06:05

n0t
Contributor
Registered: 2008-11-24
Posts: 26

Re: Proxmark3 board build pictures

Try to check your cable make sure you have the correct pins.
Pin 1 referenced below:
2isjtwm.jpg


30ikwvk.jpg

Parallel port 3  -> Pin 7 Prox
Parallel port 4  -> Pin 9 Prox
Parallel port 5  -> Pin 5 Prox
Parallel port 11 -> Pin 13 Prox
Parallel port 18-25 -> Pins 4,6,8,10,12,14,16,18,20 Prox

Also try a different computer or try changing the parallel port setting within your BIOS.
I got mine to work in ECP mode even thought the documentation says not to use it.

Hope this helps!

Last edited by n0t (2009-03-04 14:10:22)

Offline

#9 2013-11-01 11:33:10

asper
Contributor
Registered: 2008-08-24
Posts: 1,409

Re: Proxmark3 board build pictures

Which software to flash form parallel port ?

Offline

#10 2013-11-01 16:18:26

vivat
Contributor
Registered: 2010-10-26
Posts: 332

Re: Proxmark3 board build pictures

http://proxmark.org/files/Flash/
There is also schematics of wiggler jtag

Offline

Board footer

Powered by FluxBB