Proxmark developers community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

#1 2017-08-25 16:30:22

Sergio1999
Contributor
Registered: 2017-08-24
Posts: 6

Elatec TWN4 copy software read write

Good Day i am new on this site looking for some help I was thinking of buying
Elatec TWN4 but it comes is a reader only after speaking with Elatec they told me that you can buy 3 rd party software that will turn it in to a writer can some one
let me know where i can buy it? and also what is it capable of copying?  or some one has it for sale here on this site? and will it do encryption on 13.56 mhz? or
Hid Iclass or Keri i can copy every thing else  i am looking for point and click type
of set up unless some one here has another solution would relay appropriate your
Help even if i need 3 different solutions. As i am not too tec savvy.

Offline

#2 2017-08-25 17:03:41

717
Contributor
Registered: 2015-10-21
Posts: 16

Re: Elatec TWN4 copy software read write

-

717

Last edited by 717 (2017-10-04 12:49:15)

Offline

#3 2017-08-25 20:29:47

Sergio1999
Contributor
Registered: 2017-08-24
Posts: 6

Re: Elatec TWN4 copy software read write

Thank You
but is going to work as a reader? or is it going to read and write as well i know it going  work as a reader just fine Dose the factory sofware allow me to read the key fob and copy it making a  working copy?

Offline

#4 2017-08-26 20:27:30

Sergio1999
Contributor
Registered: 2017-08-24
Posts: 6

Re: Elatec TWN4 copy software read write

717 wrote:

Yes, it is going to work 100%. No need for paid software. Trust the TWN4 sales team, that is what they are here for.
On a side note, always happy we are to help on stuffs not related to the proxmark.

717

Good day Thanks for your help
so is the factory software going to work as reader .]/ writer?
or as reed only?

Offline

#5 2017-08-26 21:53:10

marshmellow
Moderator
From: US
Registered: 2013-06-10
Posts: 2,070

Re: Elatec TWN4 copy software read write

You'll need to know what you are doing to program anything.  It is possible but definitely not point and click.

Offline

#6 2017-08-29 17:53:17

Sergio1999
Contributor
Registered: 2017-08-24
Posts: 6

Re: Elatec TWN4 copy software read write

Thank YOU
My Question was do i need additional software and where can i find it? or what is the name of the software ?

Offline

#7 2017-08-29 17:54:34

Sergio1999
Contributor
Registered: 2017-08-24
Posts: 6

Re: Elatec TWN4 copy software read write

marshmellow wrote:

You'll need to know what you are doing to program anything.  It is possible but definitely not point and click.


Thank YOU
My Question was do i need additional software and where can i find it? or what is the name of the software ?

Offline

#8 2017-08-29 18:17:27

marshmellow
Moderator
From: US
Registered: 2013-06-10
Posts: 2,070

Re: Elatec TWN4 copy software read write

The software could be built using the SDK Elatec can provide.  But I'm not sure if there are pre-built ones for sale.

Offline

Board footer

Powered by FluxBB