I got the same issue with brand new Proxmark3 RDV4 ;( Emailed them once and they replied and asked for a log/picture. I sent them 2 days ago and waiting for answer.
Of course right now Proxmark is as unusable as antennas
Regards,
]]>I took of the bottom cover.. Theres a loose.. uhm.. something there.. first IC from the raw terminal on the board. Since theres an arrow underneath it I guess its a diode?
The IC is missing one leg and is so small that I do not think it would work with me trying to drop a glob of solder on each side of it. My SMD soldering skills and equipment are non-existent.
I'm following it up where I procured it.
]]>take a picture of it.
]]>I'm not sure if this goes here, in the LF board, or the Device components and Interfaces board. But i'll try.
I seem to be having some issues with the stock LF antennae my recently received RDV4, hw tune reports it as unusable. Im running latest firmware and client from the RfidResearchGroup github repo.
Testing a the antennae with a multimeter shows theres connection between the two pole (both between the screw holes and solder points).
Measuring over the pwr and gnd terminals while running hw tune show a stable 4.45/4.5 volts.
Putting a scope on the raw terminal shows.. uhm.. activity (Im not that familiar with how to use my scope....) when running hw tune.
pm3 --> hw ver
Proxmark3 RFID instrument
[ CLIENT ]
client: iceman build for RDV40 with flashmem; smartcard;
[ ARM ]
bootrom: iceman/master/ 2018-08-19 19:41:37
os: iceman/master/ 2018-08-19 19:41:39
[ FPGA ]
LF image built for 2s30vq100 on 2017/10/25 at 19:50:50
HF image built for 2s30vq100 on 2018/ 8/10 at 11:48:34
[ Hardware ]
--= uC: AT91SAM7S512 Rev B
--= Embedded Processor: ARM7TDMI
--= Nonvolatile Program Memory Size: 512K bytes, Used: 234844 bytes (45%) Free: 289444 bytes (55%)
--= Second Nonvolatile Program Memory Size: None
--= Internal SRAM Size: 64K bytes
--= Architecture Identifier: AT91SAM7Sxx Series
--= Nonvolatile Program Memory Type: Embedded Flash Memory
pm3 --> hw status
#db# Memory
#db# BIGBUF_SIZE.............40000
#db# Available memory........40000
#db# Tracing
#db# tracing ................1
#db# traceLen ...............0
#db# Currently loaded FPGA image
#db# mode.................... HF image built for 2s30vq100 on 2018/ 8/10 at 11:48:34
#db# Flash memory
#db# init....................OK
#db# Memory size.............2 mbits / 256kb
#db# Unique ID...............0xd567a882a727a126
#db# Smart card module (ISO 7816)
#db# version.................v2.06
#db# LF Sampling config
#db# [q] divisor.............95 (125 KHz)
#db# [b] bps.................8
#db# [d] decimation..........1
#db# [a] averaging...........Yes
#db# [t] trigger threshold...0
#db# USB Speed
#db# Sending USB packets to client...
#db# Time elapsed............1500ms
#db# Bytes transferred.......799744
#db# USB Transfer Speed PM3 -> Client = 533162 Bytes/s
#db# Various
#db# MF_DBGLEVEL.............1
#db# ToSendMax...............-1
#db# ToSendBit...............0
#db# ToSend BUFFERSIZE.......2308
#db# Installed StandAlone Mods
#db# LF HID26 standalone - aka SamyRun (Samy Kamkar)
pm3 --> hw tune
[=] measuring antenna characteristics, please wait...
....
[!] LF antenna is UNUSABLE
[+] HF antenna: 45.32 V - 13.56 MHz
[+] HF antenna is OK
[-] Not showing LF tuning graph since all values is zero.